|
Engine Oil Service Solution
From the first mile a vehicle is driven, heat
within the engine begins breaking down the oil.
The chemical reaction that occurs creates
varnish, then varnish and other contaminants mix
with condensation in the engine to form
sludge. It's not long before the passages that
carry the vital engine oil are restricted.
As varnish and sludge build up, friction
increases. Timing is affected. Power is lost and fuel
economy deteriorates. Even worse, the
contamination begins to clog the oil pick-up screen
- a major cause of engine failure.
The OSS process removes the varnish, carbon,
and sludge deposits that regular oil changes
can't touch. The unique OSS cleaner actually
dissolves the molecular bond between contaminants
and the internal engine parts.
Dynamic Process - OSS process is done with
the engine running, so pressure forces the cleaner
into every oil passage and return galley. The
unit's positive suction action circulates the oil
through the unit, removing loosened solids
without clogging the screen or damaging seals.
Back Flushes - When the cycle is complete,
the engine is turned off and the OSS unit reverses
the flow to be sure no blockage occurs. The
cleaning solution with suspended contamination
is purged from the engine, making it simple
to install a new filter and add fresh oil.
Fast - The process takes less than half an
hour and is self-contained. A powered discharge
transfers waste oil to a storage container
quickly and cleanly. Dispose of the waste following
standard waste oil procedures.
Operates on Shop Air - No electrical
connection is needed; power is supplied by standard
shop air.
Diagnostics - With the built-in gauges, you
can check the integrity of engine bearings - camshaft,
crankshaft, main and rod bearings. You can
also check the oil pump condition and engine
oil pressure to determine if any
problems exist.
No. 83000 - Oil contamination removal unit.
Wt., 98 lbs. Replacement Part 83020 -
OSS Process Cleaner, 32 oz. (946 ml) bottle,
12 bottles per case.
~1.
|
ENGINE FLUSH
Step 1
Heated Bilstein R-2000 Engine Flush solution is pumped through the oil
filter port at 42 PSI.
Step 2
R-2000 Engine Flush solution flows through the engine's lubrication
system dissolving sludge and varnish.
Step 3
R-2000 Engine Flush solution back flushes the oil pump pickup screen.
Dissolved sludge, varnish and debris flow to the oil pan where it is
vacuum extracted to the BILSTEIN R-2000 Engine Flush Machine.
Particulates over 3 microns are removed through three stages of
ultra-fine filtration.
Oil Changes Are Not Enough
While oil filters remove particulate over 25 microns, sludge, tar,
varnish and wear metals less than 25 microns continue to circulate
within the engine and accumulate in the passageways, oil pump and oil
pan. These contaminates cause engine wear, higher operating
temperatures, and reduced lubrication.
Past Procedures Compound the Problem
Simply pouring chemical flush additives into the crankcase is
ineffective. Dissolved sludge, particulate and accumulated debris
continue to circulate causing significant engine wear.
Bilstein R-2000™ Engine Flush System
This environmentally safe system thoroughly cleans your engine by
using patented adaptors and specially formulated solutions to dissolve
accumulations of sludge, tar, varnish and wear metals.
The process is performed with the engine off. Using pulsating
pressures, the Bilstein R-2000 circulates a heated petroleum distillate
solution through the oil pump passage ways and reservoir to dissolve
sludge.
A perfectly clean engine means better performance, superior fuel
economy and longer engine life.
Restore Engine Efficiency with Total Safety
The Bilstein R-2000 Engine Flush System will not harm your engine,
ring seating, valve guides or seals. All residual oil and cleaning
solutions are evacuated leaving a light mineral oil on critical wear
surfaces.
Periodic Engine Cleaning Extends Engine Life
Tests have shown that periodic sludge removal restores operational
efficiencies and reduces harmful exhaust emissions. By reducing wear
metals and corrosive contaminates a longer engine life can be expected.
Bilstein - Quality and Reliability
Over the decades, Bilstein has established a solid reputation for
quality and reliability. Bilstein products are marketed worldwide only
after extensive research and testing.
|
|
The
Bilstein R-2000 Engine Flush System Allows The Technician To Completely
Flush The Internal Lubrication System Of The Engine With The Engine Off.
![[Image]](pict60.jpg)
![[Image]](pict71.jpg)
